How to print QR codes: a pre-print checklist
Check these before you send a QR code to print: size for the scanning distance, quiet zone, contrast, file format, trim, finish, placement and a real test.
The short answer
Make the code big enough for the distance, keep a clear margin and strong contrast, send the printer an SVG or a high-resolution PNG, and scan a proof at full size on more than one phone. Use a dynamic code so a mistake found after printing can be fixed without a reprint.
The checklist
Go through these in order before anything goes to the printer.
- The destination works on a phone, with no login, no desktop-only page and no slow download
- The code is dynamic, unless what it holds will truly never change
- The size suits the scanning distance, about one tenth of it
- There’s a clear margin on all four sides, at least four modules wide
- The code is dark on a light background, with strong contrast
- The file is an SVG, or a PNG with enough pixels for its printed size
- The code sits inside the safe area, well away from the trim and any fold
- The material and finish won’t throw glare across the code
- The placement is easy to reach, well lit and labeled with what the code does
- A proof at full size scans on an iPhone and an Android phone
Size it for the distance
A common rule is that a code should be about one tenth of the distance it will be scanned from. A code read from one meter should be around 10 cm wide, and one read from three meters needs around 30 cm. Never go below about 2 cm (0.8 in), even for something held in the hand.
Shorter content helps at every size. A dynamic code holds a short link, so it has fewer and larger squares than a static code holding a long address.
Keep the quiet zone and the contrast
The quiet zone is the plain border around the code. Phones use it to find the code’s edges, so keep it clear of text, photos, patterns and the edge of the paper. Four modules, meaning four of the code’s small squares, is the usual minimum.
Phones look for the difference between dark and light. Dark on light is the safe choice, and black on white is the safest of all. Colors are fine if the dark one is clearly dark and the light one clearly light. Avoid two mid-tones, and test inverted codes, with light squares on a dark background, very carefully, because some phones won’t read them.
Colors can shift between screen and paper. A dark blue that looks strong on a monitor can print lighter, so judge contrast on the proof, not the screen.
Send the right file
For print, send an SVG. It’s a vector file, so it stays sharp at any size and the printer can scale it without losing the edges of the squares. If you must use a PNG, make sure it has enough pixels for the printed size. Printers often work to around 300 pixels per inch, so a code printed 2 inches wide wants a PNG of about 600 pixels or more.
Don’t use a screenshot, and don’t let anything in the workflow compress the image into a blurry JPEG. Soft edges between squares are a common reason a printed code fails.
Keep the code inside the safe area, away from the trim line, the bleed and any fold. Cutting machines move slightly, and a code clipped by a few millimeters may stop working. Don’t run a code across a fold or a binding either.
Choose the material and the spot
Glossy paper, laminate and acrylic can reflect light straight back at the camera. A matte finish is easier to scan, especially on table cards under ceiling lights. Test glossy materials in the real lighting before committing.
Curved surfaces bend the code. On bottles, cups and tubes, keep the code small relative to the curve and place it where the surface is flattest, so the whole code faces the camera at once.
Put codes where people can stop and scan comfortably: within reach, at a sensible height, and in good light. A code high on a wall, behind a counter or in a doorway where people can’t pause is easy to miss. Add a few words that say what the code does, such as “Scan for the menu”.
Test a proof, then print
Print one copy at its real size, on the real material if you can. Scan it from the distance people will actually stand, with at least two phones, in the light where it will be seen. Check that it lands on the right page, not just that the camera reacts.
If you’re printing many different codes, such as one per table, scan a handful from the final proof sheet, not only the first one.
Make mistakes fixable
Even with a careful check, things change after printing: a web page moves, a menu gets a new address, a campaign ends. With a static code, the only fix is a reprint. With a dynamic code, you change the destination and every printed copy follows from the next scan.
PikaQR’s free plan includes dynamic codes and version history. The Premium design studio adds colors, frames and logos, checks that each design still scans, and gives you print-ready PNG and SVG files.
Questions
What resolution should a QR code be for printing?
Use an SVG where you can, since it has no fixed resolution. For a PNG, aim for about 300 pixels per inch at the printed size, so a 2 inch code needs a file around 600 pixels wide.
Can I print a QR code in color?
Yes, as long as the code is clearly dark on a clearly light background. Avoid pale foreground colors and dark backgrounds, and judge the contrast on a printed proof.
Why won’t my printed QR code scan?
The usual causes are a code that’s too small for the distance, a missing margin, weak contrast, glare from a glossy finish, a blurry file or a code clipped at the trim. Fix the one that applies and print a new proof.
Can I print QR codes on a home printer?
Yes. A home laser or inkjet printer is fine for table cards, signs and test proofs. Use the SVG or a large PNG, print at the highest quality setting and check the code isn’t scaled down by the print dialog.
Related
Print codes you can still fix
Make a free dynamic code, download it as an SVG for print, and change the destination later if you need to.
Make a dynamic code